Well Water Pump Loses Pressure Quickly-Tips

Today, the use of well water pumps is not only commercial but the well water pump is becoming a domestic necessity. It is commonly found almost in every house. The purpose of the well water pump is to draw water upward from the lower level and put this water in the piping system under pressure.

This gets the water to go where you need it.

Do You know How a Well Water Pump Works?

The well water pump is designed to transport water from the lower level to a higher level. The well water pump pushes the water from the well into the storage tank where it settles down until you need it.

When the water pushes into the storage tanks, its air pressure increases, air pressure reaches a specific point it pushes the water to your home’s plumbing system.

There are two types of well water pumps are as follow:

1. Jet Pump
2. Submersible Pump

By using a submersible pump or a jet pump the well water is pumped out of the ground automatically sits on top of the ground and draws water out of the ground to create water pressure for the home.

Why Well Water Pump Loss Pressure Quickly?

The well water pump has more advantages than tap water. But it requires installation and maintenance. A properly functioning well water pump has a critical system, so there is always a point of failure. If there is low pressure the water will not drain from the tap. You have to properly check if the following

Causes of Low Pressure In Well Water Pressure

There may be several reasons for low well water pressure. Some of the reasons are as follows:

• Wrong adjustment of your pressure switch
• Clogged water line
• Water tank filled with sand and other particles
• Extra air in the Plumbing system
• Hard water
• Absence of water pressure regulator
• Plumbing infrastructure Issues
• Damaged pressure tank
• Old well Pump
• Narrow Pipelining
• Low-quality well water pump
• Leakage of Pipelining
• Excessive rust or corrosion in pressure tanks, valves, and pipelines
• Air Bladder rupture in pressure tanks
• Clogged taps, valves, nozzles, and gears

Tips To Solve The Low Water Pressure

Are you facing low water pressure? Don’t worry! Every problem has its solution. Low water pressure can easily fix. Here are some tips to solve the low water pressure that are as follows:

Tip 1: Install A Water Pressure Regulator

The water pressure regulator maintains the well water pump pressure. Normal water pressure falls between 30 to 60 psi. The water pressure regulator keeps the pressure above 30 psi. There are two types of water pressure are as follows:

1. Booster Pump
2. Constant Pressure System

A licensed plumber can measure your water pressure and suggests which regulator suits best for your well water system.

Tip 2: Check Plumbing Infrastructure Issues

Plumbing infrastructure issues can cause low well water pressure. If you want high water pressure, replace the old and defective parts of the well water pump. There may be different infrastructure issues, which are as follows:

1. Old Well Water Pump

If your well water pump is old its efficiency must be affected. Generally, the lifespan of a well water pump is about 8 to 15 years. Must check if the lifespan of your well water pump has been completed or not. Replace the well water pump if it is older than its lifespan.

2. Damaged Pressure Tank

If there is any leakage in your pressure tank, it will cause low water pressure. Must replace the damaged tank or repair the damaged part of the tank. So, you can get high water pressure.

3. Narrow Pipelining

You can’t attain high water pressure if you have narrow pipelining of the well water pump. Keep this in your mind, if the pipelining is narrow, replace this narrow pipelining to attain high water pressure.

Tip 3: Clean Clogged Nozzles, Taps, Valves, and gears

If the nozzles, taps, valves, and gears are clogged then this will hinder the path of water, and water pressure will become low. Check if the blockage is the cause of low water pressure and clean the clogged part.

Tip 4: Clean The Clogged Water Line.

Sometimes the garbage or other particles clogged in the water line, which blocks the path of water. That also causes low water pressure. Thoroughly clean the water line, so the water can flow with pressure.

Tip 5: Install Water Softener

Hard water is a type of water that has a high concentration of minerals in it. Don’t ignore this point if the well water pump is losing its pressure. The minerals in hard water can attach to pipes and get stuck in the plumbing system.

Install water softer to eliminate these minerals from the water. Installing a water softener at the water entry point to your well water tank will reduce hard water for your entire home.

Tip 6: Don’t Compromise On The Quality of the Pump

The well water pump is very essential for your domestic water use, as you can’t leave without water. So to avoid the often occurring troubles of a well water pump, don’t compromise the pump quality. A high-quality well water pump works more efficiently than a low-quality pump and causes fewer troubles.

Tip 7: Properly Adjust The Pressure Switch

The pressure switch is a mechanical component, which is commonly found at the tank tee of the pressure tank. This switch senses the water pressure in the plumbing system of your home according to your utilization and need.

Properly adjust the pressure switch. The steps to adjust the pressure switch are as follows:

1. Turn off the circuit connected to the well water pump.
2. Check the air fills valve with an air pressure meter and see where your pressure lies.
3. If the water pressure is fluctuating around 40 psi or below, increase it by adjusting the pressure switch.
4. Turn on the circuit and check out the water by opening a faucet.
5. Read again if necessary by repeating these steps.

Tip 8: Clean The Water Tank If It Is Filled with Sand

If the water tank is filled with sand and other particles the pressure in the well water pump becomes low. You should make a cleaning schedule, and clean the tank and plumbing system regularly.

Tip 9: Replace The Pressure Tank If Air Bladder Burst

Some people have a standard captive air bladder-type pressure tank. In this type of pressure tank, there is almost an indication that the bladder inside the tank has ruptured. Generally, the burst air bladder can’t repair, so, it is necessary to replace the pressure tank.

Tip 10: Call A Licensed Plumber For Service and Maintenance

If you are unable to find the reason why your well water pump loses pressure quickly, call a licensed plumber to recognize the problem and its solution.

Also, Read This: Why are Solar Lights Not Working After Rain? Tips&Tricks

Final Thoughts

Hopefully, you have got an idea that why your well water pump loses pressure quickly. If you are facing this problem, don’t panic and try to find out the actual reason for low low pressure. May the above-mentioned tips can resolve your problem.