How to Fix LED Light Remote Battery- Two Quick Solutions

An LED light remote is smaller than a TV remote. Generally, it uses coin cell batteries. In this article, you will learn how to fix the led light remote battery. if they stop working.

Sometimes, replacing the batteries does not help. Because the issue is not the dead coin cells. It happened to me just recently that I changed the remote batteries twice but still, it did not work.

So, I had to find out the root cause. I will share my personal experiences in this article and your light controller will be fixed in minutes.

Solution 1: Clean and Replace

One of the most common reasons is corrosion. The battery or the compartment gets corroded. It happens due to an extra humid environment or water contact.

Therefore, the contact is not proper and the connection is weak. Here is how can you fix the problem.

Things Required

  1. Two fresh and new batteries compatible with your LED remote
  2. One screwdriver
  3. Rubbing alcohol
  4. Cotton swabs

Step 1: Remove the Battery Cover

Next, you have to remove the entire cover of the battery compartment. It is located at the back and held with screws. So, you need a screwdriver to open the screws. Remove the cover and you should see the batteries.

Step 2: Identify the Battery

You have to check which type of batteries your LED remote uses. You can take help from the user manual for identification.

For example, it may require AA, AAA, or coin cell batteries. So, you should buy a compatible pair. Be sure to purchase high-quality batteries.

How to Fix LED Light Remote Battery- Two Quick Solutions

Step 3: Clean Everything

Take a cotton swab and dip it in rubbing alcohol. Move the cotton swab all around to remove corrosion. Replace the swab if it becomes dirty. Be sure to clean the whole battery compartment and connections.

Step 4: Fix the Wiring

Meanwhile, you should inspect the wiring inside the remote. Check all the contact points and wires. Make sure they are tightly connected.

If you notice any loose wires, re-connect them firmly. Likewise, check and replace the worn-out or damaged connections.

Step 5: Replace the Batteries

At this stage, you should have fresh and new batteries. Remove the old ones and insert the new batteries. But, do not forget to check the position. Insert the cells correctly.

Step 6: Check and Close the Remote

Before putting on the cover, check the remote. Put your fingers on the cells so that they do not fall or slip.

Now, turn ON your LED lights and check whether the remote works or not. If it works fine, put on the back cover and tighten the screws.

Solution 2: Reset Your LED Remote to Factory Settings

If replacing and cleaning do not work, you should reset the remote to factory settings. It will remove all the saved data. So, you will need to reprogram the remote control.

Step 1: Find the Reset Button

Generally, all LED remotes have a reset button. You can find it on the back, bottom, or on the sides. It is in the form of a small hole instead of an easy-to-press button. Kindly review the user manual to locate the position of the reset button.

Step 2: Take a Pressing Object

Since the button is too tiny, you cannot press it with your finger. Rather, you need a pointed object such as a pen, paperclip, or Philips head screwdriver.

Step 3: Reset the Remote

Now, insert the pressing object into the hole. Press and hold the reset button for 5-10 seconds. It will restore to factory defaults erasing all the customization.

Step 4: Test the Remote

Finally, check your remote if it is working fine. Re-program the remote and power ON your lights. Also, test other functions like brightness control and color changes.

FAQs About LED Light Remote

Following are some of the frequently asked questions by the users. Hopefully, they will help you further.

What type of batteries are required for an LED light strip remote?

Generally, LED remotes use small coin cell batteries. It is a CR2025 lithium coin cell. They are 3 volts cells and can be purchased for 4-5 dollars.

How to open the battery compartment of an LED remote?

Locate the little back tab on the bottom left or back of the remote. Squeeze a little tab in against the larger part. Pull the cover out with your finger. It will slide out easily. You can insert it back by pushing towards the inside.

Can LED lights program with more than one remote?

Yes, you can program two remotes with your LED light strips. The controller remembers the last LED strip to which it connected. So, the most recently used remote will decide the settings.

Also Read: Reset Your LED Lights Remote Top Methods

Final Words

In this Article, we explained how to Fix LED Light Remote battery. If your LED light remote is not working, you can try two fixes. First, clean the corrosion and then reset to factory defaults. After trying this, your remote batteries will be fixed and it will start working properly.

Leave a Comment