Today, the popularity of recessed lights is undeniable. Recessed lights are a versatile, aesthetic, and primary source of lighting for the room. Recessed lights are the most cost-effective, reliable, and suitable for all areas of the home.
Most of the things in the home need maintenance over time. Recessed lights also need maintenance. However, these lights have problems of their own. While convenient and aesthetic, recessed lights are associated with some issues. These issues, with possible solutions, will be discussed in this article.
Table of contents
Most Common Problem of Not Working Recessed Lights
The recessed lights are convenient. However, these lights also have problems. The recessed lights that suddenly begin to blink or trim seem like a mystery to you, but there must be a problem behind it.
The recessed lights may have problems, which are as follows:
- A sagging light trim
- Blinking light
- A blown or damaged bulb
- A blown light socket
- Incorrect Wattage
- Insulation Problems
- A faulty limit switch
- Bad wiring
- Poor Installation
- Poor Quality
If all the recessed lights are not working, it may face problems.
Problems and Tips for Recessed Lights Not Working
Mostly everyone has faced this problem because every home has lights in it. If you are facing any problem with the recessed light, read these top tips to solve your problem.
Problem 1: The Light’s Sagging Trim
Recessed lights are designed to attach to your ceiling to give a unique look to your home. You have noticed that with the passage of time splendor of the recessed lights fades away. The trim around the recessed lights starts sagging.
The primary cause of the problem may be the over-stretching of the springs, which hold the trim. Humidity in the air, ceiling, or trim low-quality material, and corrosion can also cause the sagging of light trim.
Tip: Fix The Light’s Sagging Trim
The sagging trim of the light can be easily identified. This issue can be easily resolved. Carefully clean the trim or tighten the springs of the trim. If the springs are badly damaged, then replace these trims as early as possible.
Problem 2: Blown or Damaged Bulbs
If your recessed lights are not working, there is a chance that the bulbs have blown or been damaged. The burnt and faulty bulb also causes not working of the recessed lights.
Tip: Replace the Damaged Bulbs
Replacing the blown or damaged bulbs can resolve the problem. For this, check the warranty card of the bulb. If the bulb has expired within the given time, then the company has to replace the damaged bulb. Replace the defective bulbs with new ones.
First, make sure that you turn off the switch and leave the bulb to cool down. Then disconnect the bulb from the socket and attach the new bulb.
Problem 3: The Blown Or Burnt Socket
Sometimes, due to electrical sparking, the socket has blown or burnt. If the socket has burnt or blown, the recessed lights will not work. Due to the blown or brunt socket, the bulbs can also burn.
Tip: Replace The Blown Or Burnt Socket
If the socket has been burned, there must be a gray or black spot which indicates the light is sparking. First, check these spots, and if you find these spots, replace the burnt socket and the bulbs.
Problem 4: Blinking Lights
If the recessed light fixture is blinking, there may be an issue with the thermal protection device of the lights. The thermal protection device is a black or small silver cylindrical disc connected to the fixture’s wiring junction.
Tip: Replace The Thermal Discs
In case of blinking lights, turn off the power, and access the top of the recessed fixture in the attic or crawlspace above the ceiling. Disconnect these two discs from the wiring junction and purchase the identical thermal device from the market, then again attach it to the wiring junction.
Problem 4: Over Insulation
Recessed lights are very compact. Recessed lights are made to take up a little space. If the space designed for the recessed light to fit into is too tight around the fixture, over-insulation may occur. This over-insulation causes overheating and due to this overheating, your recessed lights won’t work.
Tip: Provide Enough Space for Recessed Lights
To fix this problem, check the space and insulation around your recessed light trim are suitable to prevent the fixture from overheating.
Problem: Incorrect Wattage
Recessed lights are very cost-effective. To be illuminated, these lights use a few amperes of electricity. Sometimes, because of providing a high voltage to the recessed lights gets overheated and result in burnt-off lights.
Tip: Provide Proper Wattage To Recessed Lights
Properly provide the specifications provided by the company. Provide the properly specified wattage to the recessed lights to avoid any damage. Generally, the minimum wattage for recessed lights is 60 watts.
FAQs Related To Recessed Lights
Here is the solution to some of your confusion about recessed lights. The solutions to your questions are as follows.
What are recessed lights?
Downlight or can lights are a type of fixture light installed into the ceilings or walls.
How long will recessed lights Last?
Many recessed lights last for 50,000 hours of illumination.
What should be the arrangement of recessed lights?
Do not put recessed lighting fixtures placed too close together, or in rows down the center of the room.
What should be the minimum distance between recessed lights?
A general method for placement is to divide the height of the ceiling by two. The spacing for a room with an 8-foot-high ceiling would be 4 feet between each light.
What is the common size for recessed lighting?
The size of the recessed lighting is 6 inches.
Can we have too many recessed lights in a room?
Aesthetically, using too many recessed lights may leave areas of your room dark and may even cost you more on your electric bill.
Also, Read This: Why is my water pump not turning on?
Final Thoughts
There must be a reason for your all-recessed lights not working. Don’t bother about it. In this article, we try to discuss all the problems and their possible solutions related to the not working of recessed lights. If you are unable to solve the problem on your own, then connect to a licensed electrician.
Calm down! And hand over the problem to the expert.
